The short answer
You need a chimney rebuild when bricks are loose, spalling or leaning and the damage has spread past what repointing can fix. We take the chimney down to solid masonry, rebuild it, and add a new crown, flashing and cap. The price depends on the chimney's height, roof access, how much brick comes down and the condition of the flue.
Brick chimneys in New York take a beating. Freeze-thaw cycles, wind-driven rain and years of flue gases wear down the mortar and masonry until patching no longer holds. Chimney rebuilding means taking the damaged section down to sound brick and laying it back up with new masonry, a new crown and fresh flashing where the chimney meets the roof. FirstChoice Chimney Services rebuilds chimneys for homeowners in New York and nearby neighborhoods. A job can be a few courses of brick above the roofline or a full teardown when the structure calls for it.
Signs you need it
A rebuild is usually the answer when masonry damage has spread past what repointing or spot repair can fix. Most owners notice the problem from the ground, from the roof or inside the fireplace before they ever see a crack up close.
- Loose, spalling or missing bricks, especially near the top of the chimney
- Brick flakes, mortar sand or other debris collecting in the firebox
- White staining on the outside brick, or on inside walls next to the chimney
- Water in the firebox, or damp spots on nearby ceilings and walls after rain
- A chimney that leans, pulls away from the house or has a cracked crown
- A lasting smoke or creosote smell, or poor draft, which can point to a collapsed or blocked section of flue
- Mortar joints you can scrape out with a key or a screwdriver

What's included in a chimney rebuild
We set the scope of every rebuild after an inspection, so the exact list depends on how far the damage goes. A typical job includes:
- Inspection of the chimney inside and out, including a camera look down the flue
- A written scope showing how many courses of brick come down and what gets replaced
- Teardown of damaged masonry down to sound brick
- New brick laid with mortar matched as closely as practical to the existing color and texture
- A new crown that sheds water away from the flue
- New step and counter flashing where the chimney meets the roof
- An evaluation of the flue liner, with a separate quote for liner repair or replacement if needed
- A new chimney cap with screening to keep out rain and animals
- Debris removal and cleanup of the roof, yard and work area
- Photos of the finished work and a final walkthrough
How we work inside your home and on the roof
Most rebuilding happens outside, but the fireplace and flue still need attention. Inside, the crew lays drop cloths from the door to the hearth and seals the fireplace opening so mortar dust and soot stay out of the room. HEPA vacuums run during any work in the firebox. Before new masonry goes on top, rotary brushes clear creosote and loose debris from the flue. A camera inspection lets us check the liner and the joints we can't see from the top or the bottom.
On the roof, we set up roof protection and ladder or scaffold access suited to the building's height. Old bricks and mortar come down in buckets or chutes and are never tossed off the edge. We work in sections so the chimney isn't left open to the weather overnight, and we tarp the top if a job runs more than one day.
Time for your annual chimney check?
The standard we follow
Our chimney work follows NFPA 211, the standard that calls for chimneys, fireplaces and vents to be inspected once a year. Chimney professionals use three inspection levels. Level 1 applies when nothing has changed. Level 2 applies when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Level 3 applies when a hidden hazard can only be reached by opening part of the chimney or building. A rebuild usually starts with at least a Level 2 inspection. Sometimes we move to Level 3 once old masonry comes off and we can see what's behind it.
In New York City, a building that converts its boiler from oil to gas must have its chimney evaluated as part of that work. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue. If you are planning a conversion, it makes sense to schedule the rebuild and the liner together so the masonry and the flue are both ready for the new appliance.
What affects the price
We price each rebuild after seeing the chimney in person. The main factors are:
- Chimney height and roof access, including roof pitch and whether scaffolding is needed
- How many courses of brick need to come down, or whether the chimney needs a full teardown
- The fuel the chimney serves: wood, oil or gas
- Flue size and condition, and whether a new liner is needed
- How much creosote or soot has to be cleaned out before work starts
- Whether a camera inspection or related repairs, such as crown or flashing work, are needed
- Matching brick and mortar on older masonry
How a visit works
It starts with an inspection. A certified technician checks the chimney from the roof, the firebox and the flue, and runs a camera where it's useful. You then get a written scope and estimate, with photos, that explains what we found and what we recommend.
Once you approve the work, we schedule the rebuild around the weather, because masonry needs dry, above-freezing conditions to cure properly. If your building relies on the chimney for heat, keep in mind that New York City's heat season runs from October 1 through May 31. Doing the work in late spring or summer keeps your heating system available when you need it. On the day of the job, the crew protects your home, takes down and rebuilds the damaged section, installs the crown, flashing and cap, and cleans up. We finish with a walkthrough and photos of the completed chimney.

